Open the tool →

Mictrack Config Tool — Help & Tutorial

How to configure your MT700, MT710, MT600 or MT600-NB GPS tracker over USB, right from your browser — no software to install.

Overview

This configuration tool runs right in your browser — no software to install. It connects to your tracker through the USB cable and lets you set the APN, server, network region, and working mode, then writes everything to the device with one click.

It works on Windows, macOS and Linux using the Google Chrome or Microsoft Edge browser. (Safari and Firefox do not support the USB serial feature.)

Before you start

On Windows 11, if the port does not appear at all, see Fix the USB driver on Windows 11 →
On a Mac, install the PL2303 driver from the App Store — then approve it in System Settings → Privacy & Security and restart, or the port will never appear.

Step 1 · Connect your device

  1. Connect your device to the computer with the USB Config Cable.
  2. Make sure the device is powered on (blue LED on).
  3. Click Scan Ports. Your browser opens a small device picker — select your USB Config Cable (it may be listed as “USB-Serial”, “Prolific…” or “CH340”) and confirm. The tool then connects automatically. (The pop-up's confirm button is called Connect.)
  4. When you see Connected and the model badge (MT700 / MT710 / MT600 / MT600-NB), you're ready.
If you see “Waiting for the device…”, the device is asleep or off: press its power button once (blue LED on). That's all — the tool keeps trying and connects by itself. If it still can't connect after a while, it tells you the next step.

Step 2 · Configure

In the Setup tab you'll set two groups: Network and Working Mode.

For an MT700 / MT710 that's already configured, the top of the Setup tab shows On your tracker now (read-only). The form below it is what will be written when you click Apply — it does not change by itself. To change just one thing, click Copy to the form below first, then edit only what you need.

Network

FieldWhat to enter
APNThe APN of your SIM card. ⚠️ Confirm it with your SIM provider — a wrong APN stops the device from getting online.
Server & PortThe address and port of the tracking server your device should send data to (for example demo.traccar.org : 5030). Enter your own server here.
RegionPick USA / Canada or Australia / NZ if the device is used there; everywhere else (Europe, Asia, Africa, Latin America, the Middle East…) pick Global. This sets the correct network bands automatically. Some models (MT700L / MT710L) have no region setting.

Working modes

The working mode decides how often the device reports its location — the trade-off between tracking frequency and battery life.

MT700 / MT710

ModeBest forNotes
Mode 1 — Real-timeFirst test / live trackingReports at a fixed interval (10–600 s). Recommended for your first test — it uses the most battery, so switch to Mode 7 or 3 once everything works.
Mode 7 — Smart Low PowerMost use casesReports every few minutes when moving, every 1–24 hours when still. Best balance of tracking and battery.
Mode 0 — MixFast tracking while movingReports every few seconds when moving, every 1–24 hours when still. Slightly higher power than Mode 7.
Mode 3 — Ultra Low PowerLong-term assetsMaximum battery life; reports every 1–24 hours.
First time testing? Use Mode 1. Low-power modes sleep when the device isn't moving, which can look like the device is offline — that's normal behavior, not a fault.
Need a mode that isn't listed? Use Advanced → Advanced Command to type a MODE command directly. See the working mode guide →

MT600 / MT600-NB

MT600 devices use ACC (ignition) state instead of preset modes. You configure three reporting intervals independently:

IntervalWhen it appliesRange
ACC ONIgnition is on (vehicle running or stationary with engine on)10–65535 sec
ACC OFF — MovingIgnition is off but the vehicle is moving (towed)10–65535 sec
ACC OFF — ParkedIgnition is off and vehicle is stationary2–1440 min

Step 3 · Apply Settings

  1. Click the green Apply Settings button at the bottom. The tool first re-reads the device that is plugged in.
  2. A review window shows, in plain words, what will change on the device (old → new) and what stays the same. The raw commands are under Show commands. Click Confirm & Apply to send.
  3. The tool writes each setting in order and shows the progress.
  4. When done, the device saves and restarts automatically. The tool stays connected, so you can watch the device's boot messages live in the Device Log — no need to reconnect.
  5. After the restart the tool reads the settings back and confirms they were saved.
If a step gets no reply, the result says Not applied: nothing was saved and the device keeps its previous settings (it only saves at the last step). Check the device is on (blue LED) and click Apply Settings again.
After applying, wait 2–5 minutes before checking your tracking platform. The first GPS fix can take up to 2 minutes (longer indoors), so give the device time to restart and locate itself outdoors.
If the Device Log goes quiet after the restart, the device may have gone to sleep (normal in low-power modes) — press its power button and check the blue LED.

Advanced

Debug Mode

Turns on verbose logging — useful while testing. Remember to turn it off afterward, as it increases power consumption and shortens battery life.

If the tool shows a yellow “Debug mode is ON” banner after reading your device, just click Disable Now — it turns debug off and saves immediately, without restarting the device.

Advanced Command

Send one or more raw commands, one per line (for technicians). The tool wakes the device first and, unless the last line already saves (MODE, REBOOT or QTS), adds a save-and-restart at the end. MODE, REBOOT and QTS end the configuration, so only one of them is allowed, as the last line. Unknown commands are blocked.

Factory Reset (Danger Zone)

Erases all settings and restores factory defaults. Use only when you want to start over. You must type RESET into the confirmation field before the button becomes active — this prevents accidental resets.

Import / Export configuration

Use the Import / Export buttons (under Advanced → Save & reuse settings, or at the top of the configuration card on some versions) to reuse a setup across many devices.

A configuration file can contain any number of commands (4, 5, or 10+). The tool always sends MODE (MT700/MT710), REBOOT or QTS last, because they save the settings and end the configuration — so a file may contain only one of them. A file with none of them gets a REBOOT added automatically. Commands a model doesn't support (for example NWM / BAND on MT700L / MT710L) are blocked.

Device info

The Device Info tab shows the current configuration read from the device — model, IMEI, firmware, server, APN and mode. Click View Settings to refresh it.

Device Log

The Device Log panel (on the right) shows everything sent to and received from your device in real time, including the device's own boot messages.

Not working? Send us a 5-minute log

If your tracker doesn't work as expected, a 5-minute log lets our support team see exactly what it is doing. It takes about 6 minutes:

>_ Device Log 🕐 ⛶ 💾 🗑 → ETS <CFG>:ETS,OK → DBG,1 <CFG>:DBG,ON → REBOOT <CFG>:REBOOT,OK. <Trace>:… (start-up + 5 minutes) ● Session: active START▶ SET APN▶ ⋮ Debug ON▶ ⋮ Reboot▶ Reset▶ 2 7 3 4 5
Each red number is the step number below and marks the button to click in that step. Steps 1, 6 and 8 don't involve a button here. The real list on the right is longer (⋮) — scroll down in it to find Debug ON and Reboot.
  1. Connect the tracker to this tool as usual — the page says Connected.
  2. Click the full-screen button ⛶ at the top right of the Device Log (the black box). A list of buttons appears on the right.
  3. Click ▶ next to START. Wait until a green line ETS,OK appears in the log.
  4. Scroll down the list a little and click ▶ next to Debug ON. (This makes the tracker show all its messages.)
  5. Scroll down near the bottom of the list and click ▶ next to Reboot (not Reset). The tracker restarts, so the log shows its whole start-up: its settings and how it joins the network.
  6. Wait 5 minutes after the restart. Keep the cable plugged in and this page open.
  7. Click the Save button 💾 at the top of the log. A .txt file is downloaded (usually to your Downloads folder).
  8. Email that file to [email protected], with a short note about the problem.

Troubleshooting

ProblemWhat to do
No port appears after ScanCheck the cable is fully plugged in; install/repair the USB driver; on Windows 11 see Fix the USB driver on Windows 11. On a Mac, install the PL2303 driver from the App Store, then go to System Settings → Privacy & Security, scroll down and click Allow next to the blocked driver, and restart your computer — the port won't appear until you do.
Port appears but won't connect (“Could not open the port”)Usually one of two things:
1) The device is asleep — press its power button until the blue LED is on; the tool keeps trying for 30 seconds and connects by itself.
2) The USB driver — open Device Manager → Ports (COM & LPT). If the cable shows as “Prolific USB-to-Serial Comm Port (COMx)”, the driver is fine (it's case 1). If it shows “PL2303TA… Windows 11” or there is no COM port, see Fix the USB driver on Windows 11.
Also close any other browser tab or program that may be using the cable (e.g. a serial terminal tool).
"Scan Ports" button does nothingYou're likely not in Chrome or Edge. Open this tool in Google Chrome or Microsoft Edge on a computer.
“Waiting for the device…” / device not respondingThe device is asleep or off. Press its power button once (blue LED on) — the tool keeps trying and connects by itself. If it still doesn't answer after a minute, charge the device and click Retry.
Device doesn't show on the platform after ApplyMost often the device simply hasn't been added on the platform yet: add it with its IMEI (shown at the top of this tool). Wait 2–5 minutes, take the device outdoors for the first GPS fix, and double-check the APN with your SIM provider. Still nothing? Send us a 5-minute log.
Device Log goes silent after a restartThe device may have gone to sleep (normal in low-power modes). Press its power button and check that the blue LED comes on.
Battery drains fastTurn Debug Mode off, and consider a low-power working mode (Mode 7 or 3).

Fix the USB driver on Windows 11

First, check whether you need this. Press Win + X → Device Manager and open Ports (COM & LPT).
✅ The cable shows as “Prolific USB-to-Serial Comm Port (COMx)” → the driver is fine. The device is probably asleep: press its power button until the blue LED is on — the tool connects by itself.
❌ It shows as “PL2303TA… WINDOWS 11…”, or there is no COM port → follow the steps below.

Use this if, on Windows 11, the tool finds the port but cannot connect (“Could not open the port”), or the port doesn't appear at all — and in Device Manager the cable shows up as “PL2303TA不支援WINDOWS 11及后续版本,请洽询购买厂商”. The cable itself is fine; Windows just loaded a driver version that doesn't support it. Switch back to the older driver:

  1. Press Win + X on your keyboard and choose Device Manager.
  2. Expand Ports (COM & LPT), right-click the entry named “PL2303TA不支援WINDOWS 11…”, and choose Update driver. Device Manager: right-click the PL2303TA entry and choose Update driver
  3. Choose Browse my computer for drivers. Choose Browse my computer for drivers
  4. Click Let me pick from a list of available drivers on my computer. Click Let me pick from a list of available drivers on my computer
  5. Keep Show compatible hardware ticked, select the 2015 version — Prolific USB-to-Serial Comm Port Version: 3.6.81.357 [9/4/15], then click Next. Select the 3.6.81.357 (2015) driver version and click Next
  6. Wait for “Windows has successfully updated your drivers”, then click Close.
  7. The cable now shows as Prolific USB-to-Serial Comm Port (COMx) — it's fixed. Go back to the tool and click Scan Ports — it connects by itself. Device Manager now shows Prolific USB-to-Serial Comm Port (COM10)
If the problem comes back later (Windows Update can reinstall the newer driver), just repeat steps 2–6.

Prefer a video? Watch the same steps as an animation →

FAQ

Do I need to install any software?No. The tool runs entirely in your browser. Just use Chrome or Edge on a computer.
Which browsers are supported?Google Chrome and Microsoft Edge on desktop. Safari and Firefox don't support the USB serial feature.
Is my data sent anywhere?No. All communication happens locally between your browser and the device over USB. Nothing is uploaded.
Can I configure many devices the same way?Yes — set up one device, click Export, then Import that file on each other device.
Why does my device go "offline" in low-power modes?That's by design. In low-power modes the device sleeps when stationary and only reports periodically. For continuous tracking, use Mode 1.
Still stuck?Send us a 5-minute log (step by step, about 6 minutes) — that's the fastest way for us to see what's wrong. You can also visit help.mictrack.com or the community forum.

What's new

Oct 10, 2026 · v1.2.43
  • Not working? Get help — a button at the top of the tool (and in problem messages) opens new step-by-step help: send us a 5-minute log in 8 simple steps.
  • Clearer results — if a step gets no reply, the result now says Not applied (no green tick), where it stopped and what to do next. Factory reset and “Disable Now” only report success when the device confirms it.
  • Fewer clicks — picking the cable in the browser pop-up now connects straight away. If the device is asleep, just press its power button — the tool keeps trying and connects by itself. Unplugging and replugging the cable reconnects automatically too.
  • Safer batch work — before writing, the tool re-reads the device that is actually plugged in, so swapping to the next unit on the same cable can't mix up models or settings.
  • Battery reminders when Mode 1 or Debug is on, and a reminder to add the device's IMEI on your tracking platform.
  • Saved or not? After Apply restarts the device, the tool reads the settings back and confirms they were saved — or names the setting that differs. With Debug on it also tells you when the server has acknowledged the device's first report.
  • Import files: MODE, REBOOT or QTS is always sent last, and only one of them is allowed. Commands a model doesn't support now say so (e.g. “not supported on MT700L”) instead of “unknown command”.
Oct 10, 2026
  • On your tracker now (read-only) — after connecting, the top of Setup shows the APN, server, working mode, region and debug setting the device already has, so a configured device no longer looks empty. Click Copy to the form below to copy them into the form, change only what you need, then Apply.
  • A leftover red “APN cannot be empty” message no longer carries over after disconnecting and reconnecting.
Jun 20, 2026
  • Apply preview — clicking Apply now shows a full list of commands before anything is sent. Review and confirm, just like Import.
  • Factory Reset guard — type RESET to unlock the reset button, preventing accidental wipes.
  • Reboot hint shown below the Apply button — a reminder not to unplug during the write sequence.
  • Mode 7 description updated to be self-contained (no longer references Mode 0).
Jun 16, 2026
  • MT600 and MT600-NB support — vehicle trackers with ACC-based reporting. Three intervals: ACC ON, ACC OFF moving (towed), ACC OFF parked. Device family detected automatically on connect; the UI adapts accordingly.
Jun 15, 2026
  • Optional APN username & password for SIMs that require authentication.
  • PWA now works fully offline after first visit.
  • Security fix: user-typed commands are no longer echoed unescaped in error messages.
Jun 11, 2026
  • Configure a real MT700 / MT710 over USB — no longer a demo.
  • Model, IMEI and firmware detected automatically on connect.
  • Simpler Network setup — APN, Server and Port now on one row.
Jun 2026 — initial release
  • One-click Apply & Reboot with guided working modes.
  • Import / Export configuration as a command list.
  • Device Log with save-to-file, plus offline app (PWA).